Case 580 backhoe loader is a versatile machine designed to perform a wide range of tasks. In 1982, this backhoe loader entered the hundred best industrial machines manufactured by the United States. After that, the car endured many different changes. If we compare the samples of those years and models produced in the period from 2011 to 2012, the new ones are significantly superior in performance indicators to earlier machines. They have increased productivity and reliability, and also one of the key features are the front-facing shovel of the reverse type and hydraulic coupling of devices.
The Case 580 loader-digger has the function of locking the differential of the front or rear axle and all-wheel drive, thanks to which a high throughput of the machine was achieved.
Under the hood of this model is a four-cylinder engine brand 445T / M2. This power unit is actually the development of the company Case. Its rated output power is 71 kilowatts or 95 horsepower.
The model is widely distributed, which is explained not only by the operational characteristics, but also by the multitude of dealer points located in many countries of the world. In this regard, the search for the necessary spare parts will not cause a long time and large expenditure of funds. The machine is also very popular in the USAn markets for various special equipment.
Backhoe loader Case 580 has a fairly extensive range of attachments, which allows it to do any kind of work in many areas of activity. This machine is designed for the use of additional equipment such as:
Hydraulic breaker model CASE CB65S. The mass of this unit is 315 kilograms. The diameter of the installed peak is 63 millimeters. The lowest required oil flow is 25 liters per minute. The largest required oil flow is 100 liters per minute. The minimum working pressure has a value of 100 atmospheres. The maximum working pressure reaches 145 atmospheres. The minimum frequency of strokes is 400 beats per minute. The maximum frequency of strokes is 2000 beats per minute. The noise level of this equipment is 121 decibels. The construction height is 1389 millimeters. The width has a value of 222 millimeters. This hydraulic hammer is produced in Finland.
Hydraulic breaker model CASE CB80S. The mass of the equipment is 275 kilograms. The diameter of the installed peak is 50 millimeters. The lowest required oil flow is 35 liters per minute. The largest required oil flow is 90 liters per minute. The minimum working pressure is 90 atmospheres. The maximum working pressure has a value of 220 atmospheres. The minimum frequency of strokes is 600 beats per minute. The maximum frequency of strokes is 1800 beats per minute. The noise level of this equipment is 122 decibels. Structural height reaches 1261 mm. The width reaches 380 millimeters. This hydraulic hammer is produced in Finland.
Hydraulic breaker model CASE CB90S. The mass of such equipment has a value of 360 kilograms. The diameter of the installed peak is 80 millimeters. The lowest required oil flow is 40 liters per minute. The largest required oil flow is 120 liters per minute. The minimum working pressure is 80 atmospheres. The maximum working pressure has a value of 220 atmospheres. The minimum frequency of strokes is 500 beats per minute. The maximum frequency of strokes is 1700 beats per minute. The noise level of the hydraulic breaker has a value of 127 decibels. Structural height is 1692 millimeters. The width is 340 millimeters. This hydraulic hammer is produced in Finland.
Planning buckets. This equipment is indispensable for any construction company, since in addition to the planning of the working site, this tool is used to clean the road slopes, embankments and canals. It can also be used in leveling channels of canals and rivers of shallow depth and in removing the top layer of soil before construction itself. There are only two options for this type of equipment, namely, a bucket with a width of the lower cutting edge of 1200 millimeters and a bucket with a width of the lower cutting edge of 1500 millimeters.
Trapezoid bucket. This type of bucket is intended for making earthmoving work, in which the emphasis is on the accuracy of the width and profile of the slope. The unusual shape of the bucket allows for digging to avoid crumbling the soil back into the ditch. Often such equipment is used for digging trenches, roadsides, ravines, gutters, canals, as well as for digging fire ditches. At the highest point of the bucket, the width reaches exactly 1000 millimeters. At the lowest point of the bucket, the width is 200 millimeters. There are two teeth located at the edges of the bottom edge. Front utility dump. The main purpose of this equipment is to clean sections of streets, roads and other territories from large amounts of snow or debris. There is a rubberized bottom edge, due to which the blade is able to perform a full cleaning with small irregularities of any sections. The mass of this blade is 311 kilograms. Constructional width is 2800 millimeters. Height is 940 millimeters. There are a choice of two types of rotary mechanism: mechanical or hydraulic. The maximum angle of rotation is plus / minus 30 degrees. Frontal dump of angular type. This unit is able to cope with a large amount of snow than the previous one. This dump is applied when cleaning road sections, highways, airport runways and train stations. There are two options, distinguishable by width and weight. The first has a width of 2100 millimeters and a mass of 700 kilograms, when the second has a width of 2700 millimeters and a mass of 810 kilograms. Landscape copying is plus / minus 15 degrees. The angle of rotation is maximally changed by plus / minus 30 degrees using a hydraulic system. Snowplow auger type. The equipment refers to the units of public utilities and is also used to clear the streets and road sections from a large snow mass.
There are only two options:
Option 1. The working width is 2100 millimeters. The diameter of the installed auger is 650 millimeters. The rotary deflector is mounted either mechanical or hydraulic. Turning the pipe has a value of 240 degrees. The maximum height of snow is 650 millimeters. The discharge distance is 15 meters. The mass of this variant reaches 500 kilograms.
Option 2. The working width is 2500 millimeters. The diameter of the installed auger is 900 millimeters. The rotary deflector is mounted either mechanical or hydraulic. Pipe turning is 240 degrees. The maximum height of snow is 1200 millimeters. The discharge distance is 20 meters. The mass of this option reaches 1600 pounds. Road brushing equipment. Designed to clean the streets, road sections and other areas of snow, debris and various contaminants. The maximum pressure in the hydraulic system is 20 megapascals. The working flow of hydraulic fluid has a value of 125 liters per minute. The diameter of the set brush is 850 millimeters. The width of the grip is 2300 millimeters. The angle of rotation is maximally changed by plus / minus 30 degrees using a hydraulic system. 10. Boring attachments. The maximum oil flow is 170 liters per minute. The minimum oil flow is 95 liters per minute. The maximum pressure in the hydraulic system is 207 atmospheres. The diameter of the mounting hole for the screws is 900 millimeters. Modifications Excavator-loader Case 580 is available in two versions, namely, the basic Case 580 and the modified Case 580T.
The latter uses a modified rear axle, namely, the brakes and gearboxes were transferred to the hubs. This solution has reduced the time required for maintenance, as it is no longer necessary to completely remove the rear axle. Some cars are equipped with a limited slip differential, which provides the car with increased permeability.